GY6 150cc

 
     
    121 - 240 of 256 items
    TRS Ruckus Throttle Cable Adapter TRS  Mikuni DF-44 Fuel Pump & GY6 Coil Bracket COIL NOW INCLUDED TRS Honda Ruckus Headlight Lowering Kit  Bolt-On! 3 COLORS
    TRS Ruckus Throttle Cable AdapterTRS Mikuni DF-44 Fuel Pump & GY6 Coil Bracket COIL NOW INCLUDEDTRS Honda Ruckus Headlight Lowering Kit Bolt-On! 3 COLORS

    Tired of trying to figure out what throttle cable to use on your GY6 carb when you swap it into your Ruckus? You need this part! Don't worry about having to hack up the GY6 cable bracket anymore to use your stock Honda Ruckus Throttle cable on...

    A GREAT answer as to where to put that ugly coil! Mount it down out of the way with your fuel pump, and hide them! This clever mount is designed to use the 2-bolt type coils, along with the popular Mikuni DF-44 Fuel Pump! With this bracket you...

    Finally a BOLT-ON solution to lowering your headlights! No more need to send in your headlight frame for welding, you can just buy this simple bracket kit, and lower them yourself! Give your Ruckus a much lower,

    $17.99

    $15.29

    $49.00

    $44.10

    $48.00

    $40.79

    TRS  Mainfold  intake riser flange  31mm DANMAXX GY6 ENGINE SWAP HARNESS W/ CDI , RELAY, COIL , REC. DANMAXX GY6 REAR DUAL HUB PATTERN 4X4 AND 4/110 Blk or Raw
    TRS Mainfold intake riser flange 31mmDANMAXX GY6 ENGINE SWAP HARNESS W/ CDI , RELAY, COIL , REC.DANMAXX GY6 REAR DUAL HUB PATTERN 4X4 AND 4/110 Blk or Raw

    The GY6 Intake Manifold Riser is here! Are you running the Angled Clocking Flange, and your air filter is sitting a bit too close to the cross-bar on the frame? This Intake Manifold Riser can help you get a better fitment! This raises the Angled...

    Parts Shop MAX Honda Ruckus 150cc GY6 motor swap harnes with CDI , COIL , RECTIFIER, AND STARTER RELAY WHEN BOUGHT THROUGH THE RUCK SHOP. MAX GY6 Ruckus Wire Harness Features: ~ Made for GY6 motor with stock or aftermarket controls ~ More...

    Dual Pattern, 4 lug 4 inch lug spacing, four 12mm x 1.25 thread studs, for use with golf cart wheels OR 4x110 ATV pattern M10mmX 1.5MM For use with wheels measuring 3 inch back spacing and 4 or 5 inch front spacing 10 or 12 inch dimeter is OK....

    $29.99

    $23.99

    $175.00

    $168.00

    $150.00

    $142.50

    Dr. Pulley Roller 18X14 Weights GY6 sizes 10-14 grams Dr. Pulley Slider GY6 18X14 Weights 9 - 13 grams DYNA BEADS TIRE BALANCING CERAMIC BEADS
    Dr. Pulley Roller 18X14 Weights GY6 sizes 10-14 gramsDr. Pulley Slider GY6 18X14 Weights 9 - 13 gramsDYNA BEADS TIRE BALANCING CERAMIC BEADS

    Dr. Pulley 18X14Round Roller Weights for 125/150cc 4-stroke GY6 engines.
    Dr. Pulley Round Roller Weights have exceptional durability, heat resistance and are low friction and low wear.

     

    Dr. Pulley 18X14 Slider Roller Weights for 125/150cc 4-stroke GY6 engines.
    Dr. Pulley Slider Roller Weights have exceptional durability, heat resistance and are low friction and low wear.

    Motorcycles and Scooters ride s-m-o-o-t-h with Dyna Beads ®! You simply won't believe the ride... Glass smooth ride, every time, all the time. Dramatically longer tire life No rebalancing No spoke or rim weights Eliminates tire cupping. Easy...

    $14.99

    $13.49

    $22.99

    $18.39

    $15.99

    $15.19

    Engine Rebuild Kit; GY6 Bearing and Gasket set  57.4 stock bore Exhaust Cap Nuts for GY6 150cc 125cc QMB139 & Honda 49cc engine Exhaust studs for GY6 150cc and  Honda 49cc engine M6
    Engine Rebuild Kit; GY6 Bearing and Gasket set 57.4 stock bore Exhaust Cap Nuts for GY6 150cc 125cc QMB139 & Honda 49cc engineExhaust studs for GY6 150cc and Honda 49cc engine M6

    The perfect kit to completely rebuild your GY6 125/150 scooter. Whether it's a blown crank, or a frozen top end, this engine rebuild kit will do the trick perfectly when you get into those situations. The NCY Gasket set really makes this kit...

    Exhaust Cap Nuts for GY6 150cc/125cc and QMB139 50cc engines.

    Exhaust studs for GY6 150cc/125cc,QMB139, & Honda 50cc engines . M6 can be used on both 49cc and 150cc gy6 . HONDA 49cc use 6mm and most stock gy6 use 6mm as well. Big Bore Heads usually use M8.

    $48.99

    $1.99

    $1.79

    $1.99

    $1.79

    Final Drive Case Gasket (rear); GY6 FREE SHIPPING FUEL FILTER 90 TURN HORIZONTAL Gates Power Link Premium Belt  835-20-30 stock size
    Final Drive Case Gasket (rear); GY6 FREE SHIPPINGFUEL FILTER 90 TURN HORIZONTALGates Power Link Premium Belt 835-20-30 stock size

    Transmission cover gasket on GY6 125 - 150cc engines

    PERFECT STOCK OEM REPLACEMENT FUEL FILTER

    Gates Premium Power Link drive belt size 835-20-30 for 150cc and 125cc GY6 based 4-stroke engines. Specifically designed for a variety of motorized CVT applications including street-legal scooters and go-kar

    $5.99

    $4.79

    $6.95

    $6.25

    $24.99

    $23.74

    Gates Power Link Premium Belt 842-20-30 GIFT CERTIFICATE IN $25, $50, $75 OR $100 GY6  / GET MOTOR FLYWHEEL PULLER
    Gates Power Link Premium Belt 842-20-30GIFT CERTIFICATE IN $25, $50, $75 OR $100GY6 / GET MOTOR FLYWHEEL PULLER

    Gates Premium Power Link drive belt size 842-20-30 for 150cc and 125cc GY6 based 4-stroke engines. Specifically designed for a variety of motorized CVT applications including street-legal scooters and go-kar

    HAVE SOMEONE SPECIAL THAT IS HARD TO SHOP FOR ON THEIR BIRTHDAY, HOLIDAY, OR JUST A SPECIAL OCCASION. THE RUCK SHOP HAS YOU COVERED. ORDER A GIFT CERTIFICATE IN $25,$50,$75 OR $100 DOLLAR DENOMINATIONS. EACH GIFT CERTIFICATE HAS A UNIQUE CODE THAT...

    Dennis Stubblefield MP#1 Flywheel Puller, 27mm x 1.00 Left Hand Thread (Male). Fits most import Scooters with 125cc/150cc GY6 4-stroke engine models as well as most Honda, Yamaha, Kawasaki, Suzuki, Tohatsu and Hodaka Scooters with Japanese...

    $24.99

    $23.74

    $0.00

    $17.99

    $17.09

    GY6 11 coil POLE  Stator AC GY6 11 Pole / coil Stator 6Wire and 11 magnet  Flywheel combo AC GY6 125-150cc Carburetor 24mm
    GY6 11 coil POLE Stator ACGY6 11 Pole / coil Stator 6Wire and 11 magnet Flywheel combo ACGY6 125-150cc Carburetor 24mm

    11 Coil Stator for 150cc and 125cc GY6 4-stroke QMI152/157 QMJ152/157 engines. Specs: Triphase Full Wave A/C Diameter: 87mm Width: 30mm Bolt Hole Spacing: 41mm Bolt Hole Diameter: 6mm Coil Wire Length: 20 inches Number of Coils: 11 Plug Style:...

    Complete 11 coil pole AC , 6 wire stator & 11 magnet flywheel. OEM replacement generator for 125 - 150 cc GY6 Chinese scooter engines. Wires: 3x Yellow 1x Green 1x Blue 1x Black YOUTUBE HOW TO INSTALL STATOR VIDEO You will need a flywheel...

    24mm Intake
     Air Filter Mount (outer diameter): 41.75mm
     Electric Choke
     Polished finish
    Float drain is located on the float bowl

    $38.99

    $35.09

    $57.99

    $49.26

    $49.99

    $44.99

    GY6 150  SHORT AXLE FOR FATTY MOD Taiwan made not chinese Genuine OKO 30mm CVK Carburetor w/ electric choke Taiwan GY6 8 coil Pole Stator  AC
    GY6 150 SHORT AXLE FOR FATTY MOD Taiwan made not chinese Genuine OKO 30mm CVK Carburetor w/ electric choke Taiwan GY6 8 coil Pole Stator AC

    The Ruck Shop's Very Own. Short Axle used when installing a Fatty Tire/Rim combo with 12x8 or 10x8 rims on your GY6 Ruckus Swap. This is needed so your axle doesn't stick out like you are riding a Roman Chariot.

     

    30mm High Performance, After-Market CVK Carburetor for 150cc and 125cc GY6 4-stroke engines found on full-size street legal scooters, ATVs and off-road karts. Includes accelerator pump Air Filter Mount (outer diameter)

    8 Coil Stator for 150cc and 125cc GY6 4-stroke QMI152/157 QMJ152/157 engines. Electrical items are non-returnable, please check photos and specifications before ordering. Specs: Full Wave A/C Diameter: 88mm Width: 30mm Bolt Hole Spacing: 41mm...

    $29.99

    $25.49

    $169.00

    $135.20

    $38.99

    $29.24

    GY6 CVK Main Jet Kit  jets 100-140 sizes GY6 EXHAUST GASKET  COPPER MULTI LAYER NCY GY6 Gear Set 16x37 16X38  GY6 150
    GY6 CVK Main Jet Kit jets 100-140 sizesGY6 EXHAUST GASKET COPPER MULTI LAYERNCY GY6 Gear Set 16x37 16X38 GY6 150

    Keihin Round Style Main Jet Kit Includes The Following Sizes: 100, 105, 108, 110, 114, 115, 120, 125, 130 & 140 10 Piece Set Has 1 of Each Size Thread Size: M5x0.80 Overall Length: 8mm

    Exhaust gasket for Gy6 150cc engines by NCY. Sold individually.

    GY6 Upgear kit. 7.1% upgear. 50 ton gear press required for install. Get the most out of your big bore kit or even a stock motor, with increased top speed and a more usable rev range. 20mm W x 20mm I.D you will need a transmission gasket which we sell.

    $19.99

    $18.99

    $2.99

    $2.54

    $43.99

    $37.39

    GY6 Header Exhaust Pipe GY6 HIGH COMPRESSION FORGED PISTON WITH RINGS TAIWAN GY6 IGNITION COIL FOR COMPOSIMO TRS COMBO FUEL BRACKET
    GY6 Header Exhaust PipeGY6 HIGH COMPRESSION FORGED PISTON WITH RINGS TAIWANGY6 IGNITION COIL FOR COMPOSIMO TRS COMBO FUEL BRACKET

    Front Exhaust Pipe for 150cc and 125cc GY6 engine based Sport Style scooters

    GY6 HIGH COMPRESSION FORGED PISTON WITH RINGS , WRISTPIN AND CLIPS . SKIRTS ARE CUT TO REDUCE MASS. PISTON IS DOMED TOPPED FOR HIGHER COMPRESSION. COMES IN 61MM ,62MM OR 63MM MADE IN TAIWAN

    GY6 ignition coil for Horizontal cylinder, Honda style engines commonly found on ATVs, dirt bikes, mini choppers and pocket bikes. THIS COIL IS USED FOR COMPOSIMO COMBO FUEL PUMP / COIL BRACKET These engines can come with 2 styles of igntion...

    $19.99

    $17.99

    $99.99

    $74.99

    $19.99

    $17.99

    (1)
    GY6 Intake Manifold Gasket GY6 MANIFOLD RISER 5MM GY6 REAR DRUM BRAKE SHOES
    GY6 Intake Manifold GasketGY6 MANIFOLD RISER 5MMGY6 REAR DRUM BRAKE SHOES

    Intake manifold gasket for 150cc and 125cc GY6 4-stroke QMI152/157 and QMJ152/157 engines.

    IS YOUR CARB JUST HITTING THE FRAME. NEED A LITTLE RISE. TRY THIS 5MM RISER.

    FREE SHIPPING

    Rear Drum Brake Shoe Set for 150cc and 125cc GY6 engine based scooters. Fits other makes and models and found in many popular 13" wheel sizes. Outer Diameter: 125mm Thickness: 28mm

    $2.49

    $2.24

    $2.99

    $2.75

    $14.99

    $13.49

    GY6 Starter Clutch Nut Tool GY6 TRANSMISSION BEARING KIT GY6 WHEEL FLANGED REAR WHEEL AXLE  NUT
    GY6 Starter Clutch Nut Tool GY6 TRANSMISSION BEARING KITGY6 WHEEL FLANGED REAR WHEEL AXLE NUT

    Starter Clutch Nut Removal Tool, 1/2" Drive x 4 Prong Clutch Tool. Allows you to remove the starter clutch nut from 125cc/150cc/180cc, 4-stroke GY6 engines commonly found in Scooters, ATVs, Carts, Buggies and UTVs.

    COMPLETE TRANSMISSION BEARING KIT WITH SEAL. COMES WITH ALL BEARINGs AND GASKET. IF YOU TAKE A BUTANE TORCH AND HEAT THE BACK OF THE PLATE THE BEARING USUALLY JUST FALL OUT. WE RECOMMEND YOU GET A NEW GASKET OR USE YAMABOND OR HONDABOND SEALANT.

    GY6 WHEEL FLANGED REAR WHEEL NUT FOR GY6 125CC AND 150CC MOTORS

    $23.99

    $21.59

    $34.99

    $31.49

    $3.99

    $3.59

    HARLEY DAVIDSON 10MM BANJO WASHERS WITH SEALS (PAIR) HONDA OEM STYLE  FUEL FILTER 90 TURN HORIZONTAL HONDA RUCKUS / ZOOMER REAR FLUSH MOUNT LED TAILLIGHT TURTLE HEAD
    HARLEY DAVIDSON 10MM BANJO WASHERS WITH SEALS (PAIR)HONDA OEM STYLE FUEL FILTER 90 TURN HORIZONTALHONDA RUCKUS / ZOOMER REAR FLUSH MOUNT LED TAILLIGHT TURTLE HEAD

    HAVING ISSUES BLEEDING MASTER CYLINDER GET THESE BANJO WASHERS WITH SEAL COMES IN A PAIR WILL NEED 2 SETS IF YOU ARE DOING FRONT BRAKES. ONE SET FOR MASTER CYLINDER ONE SET FOR CALIPER SIDE.

    PERFECT STOCK OEM REPLACEMENT FUEL FILTER

    Looking to run a flush taillight that is high and tight. Look no farther. The TRS FLUSH MOUNT LED uses a quality made in the USA Light one of the brightest in the industry.

    $2.99

    $2.84

    $2.99

    $2.75

    $82.00

    $73.80

    HONDA RUCKUS Carbon Fiber Tank cover High end and Thick NCY HONDA RUCKUS CREE LED 6"  HEADLIGHT BAR W/ MOUNT 35W 3000 LUMENS Honda Ruckus Frame Splitter Alumunum Imported Ships Free
    HONDA RUCKUS Carbon Fiber Tank cover High end and Thick NCYHONDA RUCKUS CREE LED 6" HEADLIGHT BAR W/ MOUNT 35W 3000 LUMENSHonda Ruckus Frame Splitter Alumunum Imported Ships Free

    This carbon fiber gas tank cover gives the Ruckus a high end and indestructable look. Nice and thick

    TRS Honda Ruckus 6" Single Row Performance LED Light Bar Headlight Conversion Kit Product Features: Comes with Powercoated matte black brackets. NOT a 1 piece bracket. 2 piece bracket allows for better installation and bracket not warpping....

    The Honda Ruckus Frame Splitter is an easy way to cover up your coil and fuel pump? . Designed to fit over the fuel tank or its cover, the Frame Splitter really helps cover the rear section of the front sub-frame nicely when compared to the...

    $189.99

    $170.99

    $109.99

    $98.99

    $29.00

    $27.54

    HONDA RUCKUS SOLID FRONT FRAME COVER GUARD BILLET T-6061 Honda Ruckus GET, GY6, ZUMA   License Plate Mount 12 position HONDA RUCKUS MET ZOOMER LED LIGHT FLASHER RELAY
    HONDA RUCKUS SOLID FRONT FRAME COVER GUARD BILLET T-6061 Honda Ruckus GET, GY6, ZUMA License Plate Mount 12 positionHONDA RUCKUS MET ZOOMER LED LIGHT FLASHER RELAY

    Removing the OEM front frame plastics can really leave your Honda Ruckus looking bare. Well, TRS comes to the rescue with their Honda Ruckus Front Frame Cover. Cut out of 6061 billet Aluminum not just a cheap plate. These covers are attractive...

    OTTO FACTORY GY6 License Plate Mount with all hardware. Can be mounted Vertical or horizontal. Powder Coated in Black with Stainless Hardware. Mounts on the GY6 CVT case and allows you to run your plate 6 different ways. If you like it vertical...

    HONDA RUCKUS LED FLASHER RELAY WITH INSTRUCTIONS AND GROUND ALREADY WIRED. Looking to add LED Blinkers or brake lights to your scooter? You will need either a set of in-line resistors for the circuit or replace the OEM flasher with our LED...

    $64.99

    $58.49

    $38.99

    $35.09

    $13.99

    $12.59

    (1)
    Honda Ruckus Side Steps Alumunum Imported, Ships Free Left Handle Switch to use with CNC levers  V2  FREE SHIPPING Left Handle Switch to use with CNC levers  V3  FREE SHIPPING
    Honda Ruckus Side Steps Alumunum Imported, Ships Free Left Handle Switch to use with CNC levers V2 FREE SHIPPINGLeft Handle Switch to use with CNC levers V3 FREE SHIPPING

     To really set off the look of your Honda Ruckus after removing the OEM Floorboards, you need to use these Honda Ruckus Side Steps. They go hand-in-hand with the Honda Ruckus Frame Splitter.

    Left Handle Switch used with Rear Disc Brakes or our CNC brake levers. Great alternative to the Stage6 controls that seem to always be sold out. You may have to repin plug for Honda Ruckus please check OEM service manual. 

    Left Handle Switch used with Rear Disc Brakes or our CNC brake levers. Great alternative to the Stage6 controls that seem to always be sold out. You may have to repin plug for Honda Ruckus please check OEM service manual. v3 ALL BLACK BUTTONS...

    $29.00

    $26.10

    $15.00

    $12.00

    $15.99

    $14.39

    Lowboy low down Short Shock BlK Adjustable for Ruckus & GY6 NCY MIKUNI  DF-44211 FUEL PUMP REBUILD KIT GENUINE MIKUNI FUEL PUMP FOR GY6 SWAP MADE IN JAPAN
    Lowboy low down Short Shock BlK Adjustable for Ruckus & GY6 NCY MIKUNI DF-44211 FUEL PUMP REBUILD KITGENUINE MIKUNI FUEL PUMP FOR GY6 SWAP MADE IN JAPAN

    Honda Ruckus low sitting rear shock. Drop that Ruckus down to even lower and be the most slammed Ruck on your block with this black on black rear shock. Top=Eye Bottom=Clevis 235mm, eye to clevis See difference in picture compared to NCY shock

    Fuel pump rebuild kit for Single outlet pump found on Ruckus Gy6 builds. Don't buy a new pump just rebuild it.

    Mikuni Pulse Fuel Pumps employ an engine’s fluctuation in crankcase pressure to pump fuel from a remote fuel tank to an engine’s carburetor Rectangular fuel pump with 1 outlet for a single carburetor

     

    $125.00

    $93.75

    $11.75

    $11.16

    $29.99

    $28.49

    MIKUNI NEEDLE AND SEAT FOR TM 28 SERIES FLAT SLIDE CARB Mikuni TM series Flat slide Carburetor carb 28mm w/  needle Seat Multi Function Pocket Tool
    MIKUNI NEEDLE AND SEAT FOR TM 28 SERIES FLAT SLIDE CARBMikuni TM series Flat slide Carburetor carb 28mm w/ needle SeatMulti Function Pocket Tool

    RUNNING A MIKUNI TM SERIES CARB WELL YOU NEED THIS NEEDLE AND SEAT. THE FACTORY NEEDLE AND SEAT IF FOR GRAVITY FED TANKS. IF YOU ARE RUNNING A MIKUNI FUEL PUMP

    Mikuni TM series carburetors are the most popular high performance single carburetors in the sport of motorcycling. These time and track-tested carburetors have proven themselves on all terrains and in all conditions. They boast a large selection...

    Aluminum body for lighter weight. Anodized for corrosion protection and great looks. Compact size packs multi function utility. Equipped with 2, 2.5, 3, 4, 5, and 6mm hex wrenches plus an 8mm hex tip, cross head and flat head screwdrivers.

    $18.50

    $16.65

    $155.00

    $139.50

    $14.95

    $13.45

    Multi Tool with Sockets NCY 12MM X 250MM NEO CHROME FRONT AXLE FOR RUCKUS DISC KITS NCY 61mm Cylinder Kit Aluminum 171cc GY6 171 big bore
    Multi Tool with SocketsNCY 12MM X 250MM NEO CHROME FRONT AXLE FOR RUCKUS DISC KITSNCY 61mm Cylinder Kit Aluminum 171cc GY6 171 big bore

    Aluminum body for lighter weight. Anodized for corrosion protection and great looks. Compact size packs multi function utility. Equipped with 2, 2.5, 3, 4, 5, and 6mm hex wrenches plus an 8mm hex tip, cross head and flat head screwdrivers.

    TRS 12MMX250MM. Got that RRGS fork kit but no axle. Same axle that comes in the NCY AND TRS Front end Kits. Get it NOW.  Not found in States IMPORTED

    NCY GY6 150 61mm Cylinder Kit w/o head 62.5mm outer sleeve diameter. Give your GY6 based scooter some serious power with this BOLT ON (That’s right BOLT ON!) 171.3cc kit for most GY6 125/150 engines. As far as we know, this is the only 61...

    $10.99

    $25.99

    $22.09

    $156.99

    $141.29

    Aluminum Intake Manifold 30mm GY6 FREE SHIPPING NCY Racing Big Valve Cylinder Head 2 valve, 58.5mm GY6 150 NCY Racing Big Valve Cylinder Head 2 valve 61mm GY6 171cc 171
    Aluminum Intake Manifold 30mm GY6 FREE SHIPPINGNCY Racing Big Valve Cylinder Head 2 valve, 58.5mm GY6 150NCY Racing Big Valve Cylinder Head 2 valve 61mm GY6 171cc 171

    Our intake manifolds offer a smooth bore and larger inlet diameter over stock. Combined, these two assets allow more air and more fuel into your cylinder, giving you more power. Intake manifold upgrades are a must for larger carburetors. It...

     This head will allow your cylinder to breathe better! Works great with our 58.5mm cylinder assembly. Works great with the 58.5mm Cylinder or for more compression use with 61mm cylinder.

     This head will allow your cylinder to breathe better! Works great with our 61mm cylinder assembly. And you're wondering how can this get even better, right? Check out these Stainless Steel racing Valves to go with your new top end.

    $29.99

    $117.90

    $103.75

    $134.00

    $120.60

    NCY Brake Cable for ALL Frame Extension Kits Honda Ruckus +6 NCY TRS CALIPER ADAPTER 2 PISTON CALIPER NCY Clutch Springs (1000 RPM); GY6 blue
    NCY Brake Cable for ALL Frame Extension Kits Honda Ruckus +6 NCY TRS CALIPER ADAPTER 2 PISTON CALIPERNCY Clutch Springs (1000 RPM); GY6 blue

    Replacement brake cable for the following Honda Ruckus frame extension kits: 0300-0012 PASSWORD EXTENSION Overall length: 87"

     

    NCY caliper adapter. Looking to run RRGS, DIO or NCY fork but don't want to spend a fortune on Brake set up. This bracket fits on most aftermarket NCY and RRGS forks and allows you run a NCY

     

     

     

    Get better acceleration on your GY6 by upgrading your clutch springs! 1000 RPM NCY clutch springs, set of 3. Clutch springs help determine the RPM that the clutch will engage at. NOTE: THESE ARE FOR GY6 NOT THE HONDA RUCKUS 49CC. GY6 SPRINGS NO...

    $20.99

    $16.79

    $30.00

    $25.50

    $7.50

    $7.12

    NCY Clutch Springs (1500 RPM); GY6 YELLOW NCY Clutch Springs (2000 RPM); GY6 RED NCY Coated Variator (115mm/Gold color); Genuine 125/150/GY6
    NCY Clutch Springs (1500 RPM); GY6 YELLOWNCY Clutch Springs (2000 RPM); GY6 REDNCY Coated Variator (115mm/Gold color); Genuine 125/150/GY6

    Get better acceleration on your GY6 by upgrading your clutch springs! 1500 RPM NCY clutch springs, set of 3. Clutch springs help determine the RPM that the clutch will engage at. NOTE: THESE ARE FOR GY6 NOT THE HONDA RUCKUS 49CC. GY6 SPRINGS NO...

    Get better acceleration on your GY6 by upgrading your clutch springs! 2000 RPM NCY clutch springs, set of 3. Clutch springs help determine the RPM that the clutch will engage at. NOTE: THESE ARE FOR GY6 NOT THE HONDA RUCKUS 49CC. GY6 SPRINGS NO...

    The ultimate variator for your GY6 transmission! This beauty is lighter than any other variator on the market and at 115mm, is ideal for all types of riding. The teflon coated roller tracks prevent debris accumulation that causes roller weights...

    $7.50

    $6.75

    $7.50

    $7.12

    $69.00

    $58.65

    NCY Compression Spring (GY6), 1000 rpm NCY Compression Contra Spring (GY6), 1500 rpm NCY Compression Spring (GY6), 2000 rpm
    NCY Compression Spring (GY6), 1000 rpmNCY Compression Contra Spring (GY6), 1500 rpmNCY Compression Spring (GY6), 2000 rpm

    Compression springs do a couple of things. First they supply the pressure to engage the belt. They also determine the rate at which the CVT transmission changes from low to high gear. A 1000rpm spring will go into a higher gear than a 2000rpm...

    Compression springs do a couple of things. First they supply the pressure to engage the belt. They also determine the rate at which the CVT transmission changes from low to high gear. A 1500rpm spring will go into a higher gear than a 1000rpm...

    Compression springs do a couple of things. First they supply the pressure to engage the belt. They also determine the rate at which the CVT transmission changes from low to high gear. A 1000rpm spring will go into a higher gear than a 2000rpm...

    $14.00

    $12.60

    $15.00

    $13.50

    $14.00

    $12.60

    NCY Cylinder Gasket Set Sizes 57.4mm  58.5mm  61mm 63mm  GY6 NCY Drive Face (Aluminum);Genuine/GY6 NCY Exhaust Pipe Nuts (8mm, Sold in Pairs) Gy6 big bore and Grom
    NCY Cylinder Gasket Set Sizes 57.4mm 58.5mm 61mm 63mm GY6 NCY Drive Face (Aluminum);Genuine/GY6NCY Exhaust Pipe Nuts (8mm, Sold in Pairs) Gy6 big bore and Grom

    NCY Replacement cylinder gaskets for GY6 stock 57.4 all the way to a 63mm big bore kit. NCY Gasket kit. Quality replacement part.

    Choose size using drop down.

     

    High quality aluminum drive by NCY for Genuine & GY6 150cc scooters Applies to the following models: Baccio VX150 150 Baron 150-S Sport 150-VLA Classic BMS Heritage 150 Romans 150 Fly Scooters Rio 150 Genuine Blur 150 Buddy 125 Buddy 150...

    Installing a big valve head on your GY6 or large diameter pipe? These nuts are essential. The smaller, 10mm diameter head allows for extra clearance between your wrench and the pipe for easy access.

    $12.99

    $12.34

    $24.99

    $21.24

    $3.99

    $3.59

    NCY Forged Brake Caliper 2 piston - black NCY NEOCHROME TITANIUM REAR AXLE NUT/ GY6 NCY Oil Decompression Tube; Genuine,/GY6
    NCY Forged Brake Caliper 2 piston - black NCY NEOCHROME TITANIUM REAR AXLE NUT/ GY6NCY Oil Decompression Tube; Genuine,/GY6

    NCY FORGED 2 PISTON FRONT BRAKE CALIPER W/ PADS. YOU WILL NEED BANJO FITTING AND BANJO BOLT.

    High quality neochrome rear axle nut by NCY for GY6 engines. Brand: NCY Specs: M16x1.5P Fits: GY6 Engines

    Decompression tubes replace your dipstick and allow excess crank case pressure to be released. We recommend installing these tubes along side any cylinder kit. YOUTUBE INSTALL VIDEO

    $107.99

    $91.79

    $8.99

    $8.09

    $14.00

    $13.02

    TRS EGR PCV Block off Plate GY6 .25 stainless steel NCY Performance Brake Pads (Front)  Ruckus Zoomer NCY PERFORMANCE SHOCK BLACK
    TRS EGR PCV Block off Plate GY6 .25 stainless steelNCY Performance Brake Pads (Front) Ruckus Zoomer NCY PERFORMANCE SHOCK BLACK

    PCV block off plate used for removing PCV system on GY6 engines. Most GY6 scooters have sub-par PCV systems often causing massive vacuum leaks that lead to poor performance. When installing this block off plate, it is highly recommended you...

    Performance NCY front brake pads for Genuine Buddy 50.  The pad compound is long-wearing and ensures the best stopping power for your Buddy.

    These also work with the NCY Honda Ruckus front end kits.

    High-quality, NCY-built rear performance shock for Honda's Ruckus improves ride, handling, and looks great - this part is sure to improve your Ruckus and finish your custom build in style! Measurements:

    $11.99

    $9.59

    $20.99

    $18.89

    $109.00

    $98.10

    NCY Racing Brake Rear Drum Shoes (Blue) GY6 150cc+ NCY Racing Clutch ( Buddy 125/ 150 GY6 ) Gen 4 NCY Stroker Crankshaft (+2.5 mm stroke) GY6 Free shipping to 48
    NCY Racing Brake Rear Drum Shoes (Blue) GY6 150cc+NCY Racing Clutch ( Buddy 125/ 150 GY6 ) Gen 4NCY Stroker Crankshaft (+2.5 mm stroke) GY6 Free shipping to 48

    PERFORMANCE REAR GY6 BRAKE SHOES BY NCY. HAS VENTED SHOES TO PREVENT GLAZING.

     

    Very nice quality racing clutch 4th GEN. WITH 1500 SPRINGS by NCY for GY6 scooters NOT A CHINESE RACE CLUTCH THAT THE PADS COME OFF ON MADE IN TAIWAN THE BEST OF THE BEST. This is the upgraded version of the blue, third generation racing clutch....

    NCY high performance stroker crank for GY6/Buddy 150/Blur. Increases standard stroke by 2.5mm, more displacement equals more power! MUST SPLIT CASE TO INSTALL

    $20.99

    $18.89

    $65.99

    $56.09

    $200.00

    $170.00

    NCY Turbo Fan ORANGE WHITE OR CHROME GY6 NCY UNIVERSAL CNC KEY HEAD  3 COLORS NGK CR7HIX Iridium Spark Plug GY6
    NCY Turbo Fan ORANGE WHITE OR CHROME GY6 NCY UNIVERSAL CNC KEY HEAD 3 COLORS NGK CR7HIX Iridium Spark Plug GY6

    Turbo fan in ORANGE, WHITE OR CHROME for Honda/GY6 scooter engines. FITS BOTH GY6 50 AND 150 CC MOTORS

    NCY KEY HEAD IN GOLD, RED OR GUN METAL GRAY. NICE LITTLE ADDITION TO YOUR HONDA RUCKUS OR MET.

    NOTE: YOU MUST GRIND OFF TOP OF KEY TO FIT INSIDE SLOT. HAS SET SCREW.

    Got a Big Bore Kit or any performance mods you need better spark. This plug is one of the first mods that needs to be done.

    $16.00

    $14.40

    $14.99

    $12.74

    $11.00

    $10.78

    NGK CR7HSA Spark Plug NO REV LIMIT GY6 AC CDI OTTO FACTORY GY6 License Plate Mount  (Two mounting Points)
    NGK CR7HSA Spark PlugNO REV LIMIT GY6 AC CDI OTTO FACTORY GY6 License Plate Mount (Two mounting Points)

    STOCK NGK PLUG FOR GY6 Thread Size: 10mm Reach: 12.7mm (1/2 inch) Hex Size: 16mm (5/8 inch) Gap: 0.7mm (.028 inch) Heat Range: 7 Does not include terminal nut

    No Rev Limit Performance CDI with Alternating Current for 150cc and 125cc 4-stroke GY6 engines. This Performance CDIs special design removes the RPM limiter and increases firing speed at higher speeds. Please see our Warranty & Returns Policy.

    OTTO FACTORY GY6 License Plate Mount with all hardware. Can be mounted Vertical or horizontal. Powder Coated in Black with Stainless Hardware. Mounts on the GY6 CVT case and allows you to run your plate 6 different ways. If you like it vertical...

    $3.25

    $39.99

    $34.99

    $29.74

    PARTS BY  MAX 2mm STACKABLE SPACER FOR GY6 HUB TRS Ruckus Fender Washer Dress-up Kit for Battery Box  3 colors Performance Clutch Hub Drum Gy6 - FIVE BLADE
    PARTS BY MAX 2mm STACKABLE SPACER FOR GY6 HUBTRS Ruckus Fender Washer Dress-up Kit for Battery Box 3 colors Performance Clutch Hub Drum Gy6 - FIVE BLADE

    2mm stackable positive offset spacer for gy6 hub. USE THESE TO CENTER YOUR WHEEL OR TO OFFSET HUB SO AFTERMARKET WHEELS CAN CLEAR AXLE.

    $10 EACH SHIPS FREE 

    FINALLY! A Battery Box Washer Kit that fits with the right size bolts and washers. Add that last finishing touch to your project with these all new TRS battery box dress up kit! Each kit includes 4 x 5mm washers, 3 x6mm washers and stainless...

    After-Market Clutch Bell/Drum Type-1 for 150cc and 125cc 4-stroke GY6 engine based scooters, ATVs and off-road karts. Number of Splines: 19 Overall Inner Diameter: 125mm Overall Outer Diameter: 137mm Splined Inner Diameter (peak to peak): 13.5mm

    $10.00

    $9.00

    $15.75

    $14.17

    $34.99

    $31.49

    Performance Clutch Hub Drum Gy6 - SNOWFLAKE Performance GY6 ignition Coil Premium Exhaust Gasket Set
    Performance Clutch Hub Drum Gy6 - SNOWFLAKEPerformance GY6 ignition CoilPremium Exhaust Gasket Set

    After-Market Clutch Bell/Drum Type-1 for 150cc and 125cc 4-stroke GY6 engine based scooters, ATVs and off-road karts. Number of Splines: 19 Overall Inner Diameter: 125mm Overall Outer Diameter: 137mm Splined Inner Diameter (peak to peak): 13.5mm

    Igntion Coil with a single attachment for 150cc and 125cc GY6 Engine based scooters and vehicles. Please see our Warranty & Returns Policy.

    This Premium Exhaust Gasket Set includes a premium metal gasket, 2 stainless steel exhaust studs and 2 stainless steel exhaust cap nuts. Please select Exhaust Stud diameter from drop down menu.

    $33.99

    $30.59

    $15.00

    $12.00

    $14.99

    $13.49

    PWK  Genuine  OKO 28MM - 30MM SLIDE Transparent Float Bowl RRGS / ADELIN 4 PISTON BIG BRAKE KIT 3 COLORS RRGS DRAG FRONT FORKS RUCKUS GY6  BLACK (DISC) SHIPS FREE
    PWK Genuine OKO 28MM - 30MM SLIDE Transparent Float BowlRRGS / ADELIN 4 PISTON BIG BRAKE KIT 3 COLORSRRGS DRAG FRONT FORKS RUCKUS GY6 BLACK (DISC) SHIPS FREE

    This OKO clear fuel bowl is made to be used with PWK type carburetors. The clear fuel bowl aids in tuning as you can easily check the fuel level, make sure float levels are at the right height and check for debris or sediment in your fuel.

    HAVE YOUR OWN FORKS BUT ARE LOOKING FOR 4 PISTON BRAKES. RRGS OR ADELIN (WHATEVER WE HAVE IN STOCK) CALIPER BRACKET,220MM FLOATING ROTOR, TITANIUM ROTOR BOLTS , 4 PISTON ADELIN CALIPER W/ PADS (BLACK, SILVER, OR RED)

    RRGS Ruckus Low Down Front Forks The RRGS Drag Forks measure 3" shorter then the normal ncy, atr, rrgs and its about 1" shorter then the KN Low Down Forks. Custom drag forks are great for lowering your scooter without cutting springs and...

    $17.99

    $16.19

    $260.00

    $208.00

    $225.00

    $202.50

    TRS DRAG LOW DOWN  FRONT FORKS RUCKUS ( RRGS GY6) 2 COLORS RUCKUS SHORTY LOWERED FRONT BRAKE CABLE 39 INCH MADE IN USA Single Light: Black LED 60mm Anti-Vibe Post Mount  FREE SHIPPING
    TRS DRAG LOW DOWN FRONT FORKS RUCKUS ( RRGS GY6) 2 COLORSRUCKUS SHORTY LOWERED FRONT BRAKE CABLE 39 INCH MADE IN USA Single Light: Black LED 60mm Anti-Vibe Post Mount FREE SHIPPING

    TRS Ruckus Low Down Front Forks The TRS Drag Forks measure 3" shorter then the normal ncy, atr, rrgs and its about 1" shorter then the KN Low Down Forks. Custom drag forks are great for lowering your scooter without cutting springs and...

    TIRED OF ROCKING THAT LONG FRONT BRAKE CABLE WHEN YOU LOWER YOUR SHOCK FORKS? WE FIXED THAT. CUSTOM MADE FOR THE RUCK SHOP 39 INCH SHORT FRONT BRAKE CABLE TRUE 39 INCES.

     

    Black LED Light with anti-vibe post mount (replacement light for Trail Tech brackets, does not include rubber grommet.) use this the Composimo LED mount Feature Description Brightness Modes 3 (Hi - Med - Lo) Brightness 1050 Lumens (Hi mode) Beam...

    $225.00

    $191.25

    $30.99

    $27.89

    $99.99

    $89.99

    SLIDE CARB CABLE ADJUSTMENT FITTING Teflon Coated Intake Manifold (GY6) ; NCY FREE SHIPPING TO 48 ST OKO Teflon Coated SHORT Intake Manifold (GY6) 30MM
    SLIDE CARB CABLE ADJUSTMENT FITTINGTeflon Coated Intake Manifold (GY6) ; NCY FREE SHIPPING TO 48 STOKO Teflon Coated SHORT Intake Manifold (GY6) 30MM

    Did you brake yours and can't find them. We got them in stock ready to ship.

    NCY intake manifolds offer a smooth bore and larger inlet diameter over stock. Combined, these two assets allow more air and more fuel into your cylinder, giving you more power. Intake manifold upgrades are a must for larger carburetors. It...

    OKO intake manifolds offer a smooth bore and larger inlet diameter over stock. Combined, these two assets allow more air and more fuel into your cylinder, giving you more power. Intake manifold upgrades are a must for larger carburetors. It...

    $2.99

    $2.84

    $32.99

    $30.35

    $29.99

    $23.99

    The Ruck Shop  Main jet for PWK Carb CHOOSE SIZE THE RUCK SHOP / I RUCK ON THE FIRST DATE key fob The Ruck Shop pilot slow jet for PWK  Slide Carb
    The Ruck Shop Main jet for PWK Carb CHOOSE SIZETHE RUCK SHOP / I RUCK ON THE FIRST DATE key fob The Ruck Shop pilot slow jet for PWK Slide Carb

    PWK main jet that you need when running slide carb. Stock jets in carb are too big for GY6 motors or BBK. Keihin Hex Main Jet Thread Size: M5x0.80 Overall Length: 16.5mm

    THE RUCK SHOP KEY FOB ONE SIDE SAYS: I RUCK ON THE FIRST DATE OTHER SIDE : THERUCKSHOP.COM PERFECT FOR YOUR RUCKUS OR MET KEYS. COMES IN BLACK, RED, OR PINK

    PWK pilot / idle jet that you need when running slide carb. Stock jets in carb are too big for GY6 motors or BBK.

    CHOOSE YOUR SIZE 35 OR 32


       Keihin Round Idle Jet
    Thread Size: M6x0.75
    Overall Length: 28mm

    $2.99

    $2.84

    $2.99

    $2.69

    $3.99

    $3.79

    TRAILTECH VAPOR SPEEDO CABLE FOR DISC BRAKE TRS Sidewinder Headlight Bracket and 60mm LED Trailtech light TRS  Stainless Steel GY6 Starter Motor Cover  2 colors
    TRAILTECH VAPOR SPEEDO CABLE FOR DISC BRAKETRS Sidewinder Headlight Bracket and 60mm LED Trailtech lightTRS Stainless Steel GY6 Starter Motor Cover 2 colors

    THIS CABLE MAKE INSTALLATION CLEAN. WILL REQUIRE YOU TO DRILL AND TAPE YOUR BRAKE CALIPER MOUNT AND GLUE MAGNET TO ROTOR. WILL NEED USUALLY ONLY FOR SINGLE PISTON CALIPER LIKE ON NCY FRONT KIT IF YOU HAVE A RRGS DUAL PISTON CALIPER YOU WILL NOT...

    Looking to mount a single Trailtech LED headlight to your Ruckus forks, but you're too low? This is THE setup you NEED! It allows the best mounting of the Trailtech LED headlight on your Honda Ruckus no matter how low you are! The mount is...

    Hide that Ugly Starter with our TRS Stainless Steel GY6 Starter Motor Cover comes in a finish but can be easily polished or painted to match your scooter or Powdercoated High gloss Black ! Comes with stainless hardware and aluminum spacers. 

    $29.95

    $150.00

    $135.00

    $49.99

    $44.99

    (1)
    TRS 407'S 2 PIECE 12X5 REAR WHEEL RUCKUS HUB INCLIDED TRS 6MM CNC FENDER WASHERS WITH BOLTS - GOLD AND RED ONLY TRS ALL IN ONE GY6 MANIFOLD RISER ANGLED CLOCKING FLANGE 56MM V2
    TRS 407'S 2 PIECE 12X5 REAR WHEEL RUCKUS HUB INCLIDED TRS 6MM CNC FENDER WASHERS WITH BOLTS - GOLD AND RED ONLYTRS ALL IN ONE GY6 MANIFOLD RISER ANGLED CLOCKING FLANGE 56MM V2

    TRS 2 PIECE 12X5 3+2 OFFSET WITH 4/140 BOLT PATTERN. PERFECT FOR THE RUCKUS MOTOR. FREE KYMCO REAR HUB  INCLUDED HAS HUB CAP TO CLEAR AXLE AND NUT ON HUB. CAP IS ATTACHED WITH BOLTS FROM THE REAR NOT AN O-RING.

    The TRS Fender Washer Kits include (5) 6Mx20 stainless steel bolts and 5 washers. The fender washers will fit any 10mm bolt hole under the hood of your Honda or Ruckus. The 6Mx20 bolts is recommended for all parts under your hood such as...

    The GY6 Intake Manifold Riser and angled clock flange all in one is here! V2 NOW COMES IN 30MM JUST IN CASE YOU WANT TO RUN BIG BORE HEAD No more 2 piece setups that need a gasket to seal. This Intake Manifold Riser can help you get a better fitment!

    $499.00

    $424.15

    $15.00

    $12.00

    $64.99

    $59.79

    TRS AXLE SPACER KIT FOR AFTERMARKET WHEELS AND HUBS TRS BATTERY BOX FUEL / LIGHT BLOCK OFF BLACK OR RAW TRS BATTERY BOX FUEL / LIGHT BLOCK OFF W/ START BUTTON SWITCH
    TRS AXLE SPACER KIT FOR AFTERMARKET WHEELS AND HUBS TRS BATTERY BOX FUEL / LIGHT BLOCK OFF BLACK OR RAW TRS BATTERY BOX FUEL / LIGHT BLOCK OFF W/ START BUTTON SWITCH

    RRGS / NCY FRONT HUB SPACER KIT THIS KIT IS TO CENTER WHEEL FOR AFTERMARKET FRONT HUB NORMALLY USED WITH DOUGLAS, TRS, OR OTHER RUCKS WHEELS. YOU MAY HAVE TO ADD (USING WASHER) OR REMOVE (FILE) A COUPLE THOUSANTH OFF THE SPACER AS WE HAVE NO...

    NOT USING THE FUEL OR HIGH BEAM LIGHT FOR GY6 SWAPS? TRS HAS INTRODUCED THE SOLUTION. YOU NEED THE PLASTIC LED HIGH BEAM / FUEL LIGHT TO KEEP THE RIDGIDNESS FOR THE BATTERY BOX, THIS IS WHY MANY GY6 SWAPS HAVE BROKEN BOX TABS BECAUSE THEY REMOVE...

    LOOKING FOR A CLEAN PLACE FOR A START BUTTON? TRS HAS INTRODUCED THE SOLUTION. YOU NEED THE PLASTIC LED HIGH BEAM / FUEL LIGHT TO KEEP THE RIDGIDNESS FOR THE BATTERY BOX, THIS IS WHY MANY GY6 SWAPS HAVE BROKEN BOX TABS BECAUSE THEY REMOVE THIS...

    $19.99

    $18.79

    $39.99

    $33.99

    $49.99

    $44.99

    TRS Billet Aluminum Frame Caps Plugs  - 11 Styles ON SALE NOW TRS Billet Aluminum Manual CAM Timing Chain Tensioner  GY6 TRS FORWARD FOOTREST PEG LEGS FOR  HONDA RUCKUS MADE IN USA
    TRS Billet Aluminum Frame Caps Plugs - 11 Styles ON SALE NOWTRS Billet Aluminum Manual CAM Timing Chain Tensioner GY6 TRS FORWARD FOOTREST PEG LEGS FOR HONDA RUCKUS MADE IN USA

    Looking for some nice, new frame caps for your Honda Ruckus? Check these frame caps out! These caps are CNC machined from 6061 Billet Aluminum, and are held in place by a snug fitting o-ring in the side of your frame. They cover up the unsightly...

    TRS GY6 cam chain billet manual adjuster. Are you running a big Bore Kit with a oversize Crank? If so normally you need a longer chain and stock GY6 auto adjuster just doesn't work. Or maybe your tensioner is just wore out. Made in USA. Comes...

    The TRS FORWARD FOOTREST is a great addition to your ruckus for that extra leg room. Great for riders who are taller or want another leg position. Attaches to side of frame.

    $28.00

    $22.40

    $44.99

    $40.49

    $65.00

    (1)
    TRS FUEL  HOSE LINE 3/16" X 3 FT LONG SECTION TRS GY6 150cc Aluminum Spacer Gasket  for Stroker Cranks TRS Honda  Ruckus / Zoomer Ultimate CNC Handlebar Black v2
    TRS FUEL HOSE LINE 3/16" X 3 FT LONG SECTION TRS GY6 150cc Aluminum Spacer Gasket for Stroker Cranks TRS Honda Ruckus / Zoomer Ultimate CNC Handlebar Black v2

     3/16" FUEL LINE 3 FT LONG Transparent Polyurethane Fuel Line

    TRS Line is a premium polyurethane , 85 durometer, which provides for superior abrasion, kink, tear, oxidation and chemical resistance.

    LIGHT BLUE TRANSPARENT

    TRS 2.2mm, 7.9mm or 8.2mm Stroker Crankshaft Spacer for 54mm stud A-Case Cylinder Stud Spacing which is the motor we sell and most common. Use the 2.2mm for the NCY 2.2 or 2.5 stroker crank and 7.9 or 8.2mm for 8.2 crank. Remember you have head...

    The TRS ULTIMATE BAR Setup... It's The Ultimate Ruckus Steering System. Period! That's it!!! That's the name... That's what it is... You won't find a cleaner looking integrated handlebar and stem combo from anywhere else. We here at THE RUCK SHOP...

    $9.99

    $8.99

    $27.99

    $25.19

    $399.00

    $371.07

    121 - 240 of 256 items